//    Copyright (c) 1997-99 by Arthur Delcher, Steven Salzberg, Simon
//    Kasif, and Owen White.  All rights reserved.  Redistribution
//    is not permitted without the express written permission of
//    the authors.

//  Version 1.04 revised  10 May 99 to add  -l  command-line switch
//  to both  glimmer  and  long-orfs  to regard genome as *NOT*
//  circular.  Default is to regard it as circular.

Program long-orfs takes a sequence file (in FASTA format) and
outputs a list of all long "potential genes" in it that do not
overlap by too much.  By "potential gene" I mean the portion of
an orf from the first start codon to the stop codon at the end.

The first few lines of output specify the settings of various
parameters in the program:

 Minimum gene length is the length of the smallest fragment
   considered to be a gene.  The length is measured from the first base
   of the start codon to the last base *before* the stop codon.
   This value can be specified when running the program with the  -g  option.

 Minimum overlap length is a lower bound on the number of bases overlap
   between 2 genes that is considered a problem.  Overlaps shorter than
   this are ignored.

 Minimum overlap percent is another lower bound on the number of bases
   overlap that is considered a problem.  Overlaps shorter than this
   percentage of *both* genes are ignored.

The next portion of the output is a list of potential genes:

 Column 1 is an ID number for reference purposes.  It is assigned
   sequentially starting with  1  to all long potential genes.  If
   overlapping genes are eliminated, gaps in the numbers will occur.
   The ID prefix is specified in the constant  ID_PREFIX .

 Column 2 is the position of the first base of the first start codon in
   the orf.  Currently I use atg, and gtg as start codons.  This is
   easily changed in the function  Is_Start () .

 Column 3 is the position of the last base *before* the stop codon.  Stop
   codons are taa, tag, and tga.  Note that for orfs in the reverse
   reading frames have their start position higher than the end position.
   The order in which orfs are listed is in increasing order by
   Max {OrfStart, End}, i.e., the highest numbered position in the orf,
   except for orfs that "wrap around" the end of the sequence.

When two genes with ID numbers overlap by at least a sufficient
amount (as determined by Min_Olap and Min_Olap_Percent ), they
are eliminated and do not appear in the output.

The final output of the program (sent to the standard error file so
it does not show up when output is redirected to a file) is the
length of the longest orf found.



Specifying Different Start and Stop Codons:

To specify different sets of start and stop codons, modify the file
gene.h .  Specifically, the functions:

   Is_Forward_Start     Is_Reverse_Start     Is_Start
   Is_Forward_Stop      Is_Reverse_Stop      Is_Stop

are used to determine what is used for start and stop codons.

Is_Start  and  Is_Stop  do simple string comparisons to specify
which patterns are used.  To add a new pattern, just add the comparison
for it.  To remove a pattern, comment out or delete the comparison
for it.

The other four functions use a bit comparison to determine start and
stop patterns.  They represent a codon as a 12-bit pattern, with 4 bits
for each base, one bit for each possible value of the bases, T, G, C
or A.  Thus the bit pattern  0010 0101 1100  represents the base
pattern  [C] [A or G] [G or T].  By doing bit operations (& | ~) and
comparisons, more complicated patterns involving ambiguous reads
can be tested efficiently.  Simple patterns can be tested as in
the current code.

For example, to insert an additional start codon of CAT requires 3 changes:
1. The line
        || (Codon & 0x218) == Codon
   should be inserted into  Is_Forward_Start , since 0x218 = 0010 0001 1000
   represents CAT.
2. The line
        || (Codon & 0x184) == Codon
   should be inserted into  Is_Reverse_Start , since 0x184 = 0001 1000 0100
   represents ATG, which is the reverse-complement of CAT.  Alternately,
   the #define constant  ATG_MASK  could be used.
3. The line
        || strncmp (S, "cat", 3) == 0
   should be inserted into  Is_Start .



To run the program:

      long-orfs genome.seq

  where  genome.seq  is a genome sequence in FASTA format.

  Options can be specified after the genome file name

      long-orfs genome.seq <options>

  Options are:
    -g n   Set minimum gene length to n.  (Default is 500)
    -l     Regard the genome as not circular, i.e., do not allow
           genes to "wrap around" the end of the genome.
           This option works on both  glimmer  and  long-orfs .
           The default behaviour is to regard the genome as
           circular.
    -o n   Set maximum overlap length to n.  Overlaps shorter than this
           are permitted.  (Default is 30 bp.)
    -p n   Set maximum overlap percentage to n%.  Overlaps shorter than
           this percentage of *both* strings are ignored.  (Default is 10%.)

If you *DON'T* want to eliminate overlapping genes, just use the  -p 100
option.